2010 GMC Acadia
Counts come from unverified consumer complaints filed with NHTSA and cannot be compared between models — how to read them.
Common problems reported on the 2010 GMC Acadia
| Component group | Complaints | Share |
|---|---|---|
| Steering | 148 | 43.5% |
| Engine | 71 | 20.9% |
| Electrical System | 45 | 13.2% |
| Power Train | 43 | 12.6% |
| Exterior Lighting | 24 | 7.1% |
| Air Bags | 16 | 4.7% |
| Unknown or Other | 11 | 3.2% |
| Engine and Engine Cooling | 10 | 2.9% |
| Suspension | 10 | 2.9% |
| Structure | 8 | 2.4% |
| Vehicle Speed Control | 8 | 2.4% |
| Electronic Stability Control (ESC) | 7 | 2.1% |
340 complaints filed between December 14, 2009 and November 11, 2022.
At what mileage the GMC Acadia failed
| Component group | Median | Reports |
|---|---|---|
| Steering | 70,000 | 138 |
| Engine | 103,000 | 57 |
| Electrical System | 67,640 | 38 |
| Power Train | 76,000 | 32 |
| Exterior Lighting | 60,000 | 21 |
| Air Bags | 62,370 | 15 |
Across all components, half the reported failures happened before 74,618 miles, with the middle half falling between 55,000 and 103,000. Based on the 292 complaints (86%) that record a mileage.
A low figure does not mean the car stops working at that mileage. It means the reported failures clustered early, which most often points to a fault built into a production batch — usually the kind of thing a warranty repair or a recall campaign addresses.
How this mix compares with other model years
| Component group | Here | Typical |
|---|---|---|
| Engine | 20.9% | 16.6% |
| Electrical System | 13.2% | 13.4% |
| Power Train | 12.6% | 10.2% |
| Unknown or Other | 3.2% | 10.2% |
| Service Brakes | 1.5% | 6.4% |
| Steering | 43.5% | 6.2% |
| Air Bags | 4.7% | 5.8% |
| Fuel/Propulsion System | 0.6% | 4.5% |
This compares the subjects of the complaints, not how many there are. A share needs no denominator, so unlike a count it can honestly be held against a norm — but a group sitting above the typical share means people complained about that part more often relative to everything else on this car, not that the car is worse than another.
How serious the complaints were
- 1.5% Crash reported 5 of 340
- 1.8% Fire reported 6 of 340
- 1.5% Injury reported 5 of 340
- 0.3% Death reported 1 of 340
Reported across all complaints on file: 6 injuries and 1 death. These shares sit within this model’s own complaints — they say nothing about how it compares to another model.
Recall campaigns
4 campaigns. A recall repair is free at a dealer regardless of how many owners the car has had. Check the car’s own VIN — a campaign listed here may already have been carried out on it.
15V415000 Structure: Body: Hatchback/Liftgate June 30, 2015
General Motors LLC (GM) is recalling certain model year 2008-2012 Buick Enclave vehicles manufactured January 3, 2007, to February 29, 2012, 2009-2012 Chevrolet Traverse vehicles manufactured July 6, 2008, to March 9, 2012, 2007-2012 GMC Acadia vehicles manufactured September 15, 2006, to February 29, 2012, and 2007-2010 Saturn Outlook vehicles manufactured August 17, 2006, to March 18, 2010. The affected vehicles, equipped with the power liftgate option, have gas struts that hold the power liftgate up when open. These struts may prematurely wear and the open liftgate may suddenly fall.
Consequence: If the open liftgate unexpectedly falls, it may strike a person, increasing their risk of injury.
Remedy: GM will notify owners, and dealers will update the software for the power liftgate actuator motor control unit so that the motor will prevent the rapid closing of the lift gate, free of charge. The recall began on November 15, 2016. Owners may contact Buick customer service at 1-800-521-7300, Chevrolet customer service at 1-800-222-1020, GMC customer service at 1-800-462-8782, and Saturn customer service at 1-800-553-6000. GM's number for this recall is 15240.
Campaign covered 691,144 vehicles across model years 2010, 2011, 2012 — a count for the whole campaign, not for this model year alone.
14V266000 Seat Belts May 20, 2014
General Motors is recalling certain model year 2009-2014 Buick Enclave vehicles manufactured April 14, 2008, through May 14, 2014, Chevrolet Traverse vehicles manufactured June 6, 2008, through May 14, 2014, and GMC Acadia vehicles manufactured April 9, 2008, through May 14, 2014, and 2009-2010 Saturn Outlook vehicles manufactured April 14, 2008, through March 18, 2010. In the affected vehicles, the flexible steel cable that connects the seatbelt to the front outboard seating positions may fatigue and separate over time.
Consequence: If the steel cable becomes fatigued and separates, the seatbelt may not properly restrain the seat occupant increasing the risk of an injury in a crash.
Remedy: General Motors will notify owners, and dealers will inspect and, if necessary, repair and replace the lap pretensioner, free of charge. Parts are not currently available. An interim notice will be mailed to owners in July 2014. A second notice will be mailed to owners once parts become available. The recall for the 2009-2010 model years began on July 11, 2014. The interim letter for the 2011-2014 model years were distributed on July 11, 2014. Owners may contact General Motors at 1-800-222-1020 (Chevrolet), 1-800-521-7300 (Buick), 1-800-462-8782 (GMC), 1-800-553-6000 (Saturn). General Motors recall number for this campaign is 14187.
Campaign covered 1,339,355 vehicles across model years 2010, 2011, 2012, 2013, 2014 — a count for the whole campaign, not for this model year alone.
14V118000 Air Bags: Side/Window March 17, 2014
General Motors LLC (GM) is recalling certain model year 2008-2013 Buick Enclave and GMC Acadia and 2009-2013 Chevrolet Traverse and 2008-2010 Saturn Outlook vehicles. In the affected vehicles, increased resistance in the driver and passenger seat mounted side impact air bag (SIAB) wiring harnesses may result in the SIAB and seat belt pretensioners not deploying in the event of a crash.
Consequence: Failure of the side impact air bags and seat belt pretensioners to deploy in a crash increase the risk of injury to the driver and front seat occupant.
Remedy: GM will notify owners, and dealers will replace the affected harness connections with soldered connections, free of charge. The recall began on June 16, 2014. Buick owners may contact the owner center at 1-800-521-7300, Chevrolet owners at 1-866-694-6546, Saturn at 1-800-553-6000, and GMC owners at 1-866-996-9463. GM's number for this recall is 14030. Note: Vehicles repaired as part of Customer Satisfaction Campaign 10085 and special coverage 10335 have already had the subject condition repaired and therefore are not included in the safety recall.
Campaign covered 1,176,407 vehicles across model years 2010, 2011, 2012, 2013 — a count for the whole campaign, not for this model year alone.
10V375000 Seat Belts August 12, 2010
GENERAL MOTORS IS RECALLING CERTAIN MODEL YEAR 2009-2010 CHEVROLET TRAVERSE, BUICK ENCLAVE, GMC ACADIA, AND SATURN OUTLOOK VEHICLES. THE SECOND ROW SEAT SIDE TRIM SHIELD RESTRICTS THE UPWARD ROTATION OF THE SAFETY BELT BUCKLE WHEN THE SEAT BACK IS RETURNED TO A SEATING POSITION AFTER BEING FOLDED FLAT. IF THE BUCKLE CONTACTS THE SEAT FRAME, ADDITIONAL EFFORT IS REQUIRED TO RETURN THE SEAT TO A SEATING POSITION. IF SUFFICIENT FORCE IS APPLIED, THE BUCKLE COVER COULD BE PUSHED DOWN THE STRAP, EXPOSING AND PARTIALLY DEPRESSING THE RED RELEASE BUTTON.
Consequence: THE SAFETY BELT MAY NOT RESTRAIN THE OCCUPANT AS INTENDED DURING A CRASH, INCREASING THE RISK OF INJURY TO THE SEAT OCCUPANT.
Remedy: DEALERS WILL MODIFY THE SECOND ROW SEAT SIDE TRIM SHIELDS. IF A SAFETY BELT BUCKLE IS DAMAGED, DEALERS WILL REPLACE IT FREE OF CHARGE. THE SAFETY RECALL BEGAN ON AUGUST 18, 2010. OWNERS MAY CONTACT CHEVROLET AT 1-800-630-2438, BUICK AT 1-866-608-8080, GMC AT 1-866-996-9463, AND SATURN AT 1-800-972-8876, OR AT THE OWNER CENTER AT WWW.GMOWNERCENTER.COM.
Campaign covered 207,210 vehicles across model year 2010 — a count for the whole campaign, not for this model year alone.
NCAP crash-test ratings
| Variant | Overall | Frontal | Side | Rollover |
|---|---|---|---|---|
| 2010 GMC Acadia 4-DR. w/SAB | Not Rated | Not Rated | Not Rated | 4 |
Ratings are out of 5 stars.
Pre-purchase inspection checklist
Written and checked by someone who does this work; it is not derived from the data. The complaint counts decide only the order: the assemblies this model’s owners complain about most come first.
Suspension, control arms, steering
Related complaint groups: Steering (148), Suspension (10)
With the car parked
- Rock the steering wheel briskly left and right. Knocking and free play point to ball joints, tie rod ends or the rack. This is the most productive check of this assembly without a lift.
- Rock each wheel at 12 and 6 o’clock (ball joint, wheel bearing) and at 3 and 9 o’clock (steering linkage).
- Inspect the bushings for cracks and separation, and the ball joint boots for damage.
On the road
- Dull knocking from the front over small bumps. The cause cannot be determined without a lift: sway bar links are inexpensive, control arms cost several times more, and by ear the two are indistinguishable. A knock is grounds to require an inspection on a lift before purchase — not grounds to walk away from the car.
- Whether it pulls to one side on a level road, and whether the wheel returns to center after a turn.
Red flags
- Uneven tread wear — almost always alignment
- A recent alignment in the paperwork with no explanation of why
- One control arm noticeably newer than the rest
Cost if it needs work: Low to moderate. Depends on what turns out to be the source. Plus an alignment after the replacement.
Engine and cooling system
Related complaint groups: Engine (71), Engine and Engine Cooling (10)
Come to a cold car. A warmed-up engine hides a hard start, smoke and knocking. If the car is already warm, that is a yellow flag: ask for 30–40 minutes to let it cool. A refusal to let it cool is a red flag.
With the car parked
- Oil: level, color, consistency. Level above maximum plus a smell of fuel on the dipstick means the oil is being diluted with fuel.
- A whitish film on the oil filler cap alone is usually condensation from short trips in cold weather, not cause for alarm. What matters is the dipstick: a coffee-with-milk emulsion on the dipstick requires serious further inspection. A further indication is coolant hoses that are hard and under excess pressure.
- Coolant: level, color, no oil film. Open the reservoir only on a fully cooled engine.
- Leaks: under the engine, along the sump seam, around the valve cover, along the hoses and the radiator.
On the road and after
- Cold start: how long the starter cranks, smoke in the first seconds, knocking that goes away as it warms up.
- Temperature over the whole drive. Idle with the air conditioning on: the fan should cut in and the needle should not climb.
- After the drive, switch off, wait a couple of minutes and look for fresh drips under the car.
Red flags
- A freshly washed engine bay on a high-mileage car
- Thick white smoke after warm-up
- Temperature climbing in traffic
Electrical system
Related complaint groups: Electrical System (45), Exterior Lighting (24)
With the car parked
- With the ignition on, before starting, every warning light should come on and then go out once the engine runs. None coming on at all is worse than one staying lit: the bulb may have been removed or disabled in software.
- Click through everything: windows from every switch, mirrors, heated elements, climate control on all settings, the radio, the camera, the parking sensors, cruise control.
- Every exterior light, including running lights, brake lights, side repeaters and the license plate lamp.
- Battery terminals for corrosion, and the date on the battery.
- Cabin and trunk for signs of water: damp carpet under the mats, condensation in the headlights, rust on the seat mounts. Water in the electrics causes faults that are extremely hard to trace.
On the road
- Whether anything dims when several high-draw consumers are switched on at once.
- A second hot start after the drive.
Red flags
- A dashboard with no warning lights at all when the ignition is on
- Signs of water ingress
- Homemade wiring, twisted joints, tape under the dash
- Several small non-working functions at once — usually one common root cause
Automatic transmission
Related complaint groups: Power Train (43)
Checking the fluid level during an inspection is usually not possible — many cars need a lift, some have no dipstick at all, and Honda’s procedure differs from the rest. So this assessment is built on behavior, not on fluid.
With the car parked
- Move the selector P → R → D and back with the brake held. Each engagement should be a soft nudge, without a thump and without delay. Repeat two or three times in each direction.
On the road
- Shifts without noticeable delay or thump, both under acceleration and when slowing down.
- Pay particular attention to the 1-2-3 and 3-2-1 transitions — they carry the most load.
- Hard acceleration at full throttle: the revs should not flare without the car gaining speed.
- On a CVT the revs should rise smoothly, without steps, droning or jerking.
Questions for the seller
- Has the fluid been changed, and is there proof. Regular changes are a substantial plus for the car; their absence at high mileage is reason for caution.
Red flags
- A stored transmission fault code (a scan tool is worth having)
- Slipping under load in any form
- Recently cleared codes with no explanation
- The seller offering to "just change the fluid" when it is black and burnt — that is cosmetic cover over wear that has already happened
Cost if it needs work: Expensive. The most expensive of the likely assemblies; a repair is often comparable to the value of the car.
Axles and CV joints
Related complaint groups: Power Train (43)
With the car parked
- Turn the steering to full lock and inspect the outer CV boots on both sides for cracks, splits and thrown grease on the inner face of the wheel and in the wheel arch. A split boot on a joint that is still sound is a cheap repair today and an expensive one in six months.
On the road
- Empty parking lot, steering at full lock, slow circles in both directions. A rhythmic clicking points to an outer CV joint; the side is identified by the direction of the turn.
- Vibration under acceleration in a straight line that disappears when you lift off may indicate an inner CV joint.
Cost if it needs work: Relatively low. A good indicator of how the car has been treated overall.
Airbags and the VIN recall check
Related complaint groups: Air Bags (16), Seat Belts (6)
The most reliable procedure in this library — it does not depend on hearing, experience or inspection conditions.
Required procedure
- Take the VIN from the car itself — the windshield on the driver’s side, the door pillar, the paperwork — not from the listing.
- Check that VIN in NHTSA’s official recall lookup.
- A recall repair at a dealer is free regardless of how many owners the car has had. An open recall is a reason to visit a dealer, not a reason to haggle.
- An open airbag recall is grounds not to buy the car until it has been fixed.
Inspection
- The SRS light should come on with the ignition and then go out. Not coming on at all probably means it has been disabled deliberately.
- Airbag covers on the wheel and dash: uneven gaps, mismatched texture, marks from removal.
- Seat belts: pull each one out to full length and check for chafing, tears and water marks. The inertia reel should lock when pulled sharply.
Brakes
Related complaint groups: Service Brakes (5)
With the car parked
- Brake fluid level and color. Clear yellow is fresh; dark brown has not been changed in a long time.
- Fluid at the lower mark with no leaks usually means worn pads: the pistons have extended and the fluid has moved into the calipers.
- Pad thickness through the spokes of the wheel. Check the disc for a lip at the outer edge and for deep scoring.
- Inside face of the wheels: an even dark dust film is normal; one wheel noticeably dirtier than the others may indicate a sticking caliper.
- Hoses for cracks and bulges, lines for corrosion.
On the road
- First stop at low speed: the pedal should be firm, with no sinking.
- Accelerate to 40–45 mph and brake moderately. Pulsing through the pedal or the steering wheel usually means warped discs.
- Braking on flat dry pavement: pulling to one side requires further inspection.
- The ABS light should come on with the ignition and go out after the engine starts.
- A feeling that the car is driving "as if towing a trailer" may indicate binding brakes.
- The car squatting at the rear when pulling away may indicate parking-brake cables or stuck rear shoes.
After the drive
- Hold your palm near each wheel without touching the disc or the caliper — after braking they will burn you. Compare only left against right on the same axle: the front is always hotter than the rear, and that is normal. A noticeable difference between the two wheels of one axle requires further inspection.
Red flags
- The pedal slowly sinks to the floor when held down
- An illuminated ABS or brake system warning light
- Fresh fluid together with completely worn pads
Cost if it needs work: Moderate. Confirm actual cost against local prices at the time of purchase.